John Deere Tractor Error Codes for 2008-2015 Models: 5045E, 5055E, 5065E, 5075E

000084.07

Main Control Module Has Noted A Wheel Speed During A Transmission Calibration. (PTR)

000096.03

Fuel level Sender High Voltage (CCU)

000107.00

Dash Module Has Noted An Issue With The Engine Air Filter Blocked. (ICC)

000158.01

Main Control Module Has Noted A Low Module Switched 12 volt Supply Voltage. (PTR)

000162.02

Main Control Module Has Noted An Issue With The Signal Voltage From The Transmission Hi/Low Switch. (PTR)

000162.31

Main Control Module Has Noted An Issue With The Signal Voltage From The Transmission Hi/Low Switch. (PTR)

000167.04

Dash Module Has Noted A Low Battery/Alternator Voltage. (ICC)

000190.18

Main Control Module Has Noted The Engine Speed Has Not Been Received On The CAN BUS From The Engine Module. (PTR)

000191.00

Main Control Module Has Noted The Transmission Speed Sensor Speed Is Too High During Calibration (PTR)

000191.17

Main Control Module Has Noted The Transmission Speed Sensor Speed Is Too Low (PTR)

000237.02

Central Control Module Has Noted An issue With The Stored Tractor Configuration Data (CCU)

000237.02

Dash Module Has Noted An issue With The Stored Tractor Configuration Data (ICC)

000237.31

Central Control Module Has Noted An issue With The Stored Tractor Configuration Data (CCU)

000237.31

Dash Module Has Noted An issue With The Stored Tractor Configuration Data (ICC)

000598.02

Main Control Module Has Noted An Issue With The Clutch Pedal Sensor. (PTR)

000598.04

Main Control Module Has Noted An Issue With The Clutch Pedal Sensor. (PTR)

000628.02

Central Control Module Has Noted An issue With The Stored Tractor Configuration Data (CCU)

000628.02

main Control Module Has Noted An Internal Issue When Booting Up. (PTR)

000628.12

Dash Module Has Noted An Internal Issue When Booting Up. (ICC)

000630.02

Dash Module Has Noted An Internal Issue When Booting Up. (ICC)

000630.14

Central Control Module Has Noted An issue With The Rear PTO Speed (CCU)

000630.14

Main Control Module Has Noted An Issue With The Transmission Calibration Values. (PTR)

000752.03

Main Control Module Has Noted An Issue With The Shuttle Manual Sensitivity Adjustment Dial Voltage. (PTR)

000752.04

Main Control Module Has Noted An Issue With The Shuttle Manual Sensitivity Adjustment Dial Voltage. (PTR)

001504.10

Main Control Module Has Noted An Issue With The Driver Present Seat Switch. (PTR)

001638.00

Transmission Hydraulic Oil Temperature Is Very High (CCU)

001638.03

Transmission Hydraulic Oil Temperature Sensor High Voltage (CCU)

001638.04

Transmission Hydraulic Oil Temperature Sensor low Voltage (CCU)

001638.16

Transmission Hydraulic Oil Temperature Is High (CCU)

001883.00

Central Control Module Has Noted An issue With The Rear PTO Over Speed (CCU)

001883.01

Central Control Module Has Noted An issue With The Rear PTO Low Speed (CCU)

002818.31

Operator Seat Switch Not Activated With The PTO Switched On (CCU)

002820.31

Operator Seat Switch Not Activated With The Shuttle Lever Is Switched On (PTR)

002825.07

Main Control Module Has Noted An Issue With The Park Brake Active When But The Shuttle Lever Is Not In Neutral. (PTR)

003509.03

Central Control Module Has Noted A High Voltage On The 5 volt Sensor Supply Circuit. (CCU)

003509.03

Main Control Module Has Noted An issue With 5 Volt Sensor Supply Voltage. (PTR)

003509.04

Central Control Module Has Noted A Low Voltage On The 5 volt Sensor Supply Circuit. (CCU)

003509.04

Main Control Module Has Noted An issue With 5 Volt Sensor Supply Voltage. (PTR)

523316.04

Central Control Module Has Noted A Low Module Switched 12 volt Output Voltage. (CCU)

523953.02

Main Control Module Has Noted An Issue With The Signals From The Neutral Switch On The Transmission, High/Low Gear Shift Buttons, Park Lock Switch, Shuttle Lever Neutral Signal. (PTR)

524020.31

Main Control Module Has Noted The Shuttle Lever Was Not In Neutral When Tractor Was Turned On. (PTR)

524021.31

Main Control Module Has Noted The Shuttle Lever Reverse Signal Issue. (PTR)

524160.02

Main Control Module Has Noted An Issue With The Signal Voltages From The Shuttle Lever (PTR)

524173.02

Main Control Module Has Noted An Issue With The Signals From The Clutch Pedal Position Sensor. (PTR)

524173.14

Main Control Module Has Noted An Issue With The Signals From The Clutch Pedal Position Sensor. (PTR)

524173.15

Main Control Module Has Noted An Issue With The Signals From The Clutch Pedal Position Sensor. (PTR)

524173.16

Main Control Module Has Noted An Issue With The Signals From The Clutch Pedal Position Sensor. (PTR)

524173.17

Main Control Module Has Noted An Issue With The Signals From The Clutch Pedal Position Sensor. (PTR)

524173.18

Main Control Module Has Noted An Issue With The Signals From The Clutch Pedal Position Sensor. (PTR)

524224.14

Main Control Module Has Noted An Issue With The Signal From The PTO Switch. PTO Switch On Signal Received When Tractor Was Started. (CCU)

524230.05

Main Control Module Has Noted An Issue With The Supply Voltage To The Enable Trans Pressure Solenoid. (PTR)

524230.07

Main Control Module Has Noted An Issue With The Enable Trans Pressure. (PTR)

524234.03

Main Control Module Has Noted An Issue With The Enable Trans Pressure Sensor. (PTR)

524234.04

Main Control Module Has Noted An Issue With The Enable Trans Pressure Sensor. (PTR)

524235.05

Main Control Module Has Noted An Issue With The Voltage On The 4WD Circuit. (CCU)

524252.05

Main Control Module Has Noted An Issue With The Voltage On The PTO Circuit. (CCU)

524254.03

Main Control Module Has Noted An Issue With The Voltage From The Transmission Enable Solenoid. (PTR)

524254.04

Main Control Module Has Noted An Issue With The Voltage From The Transmission Enable Solenoid. (PTR)

524255.31

The Rear External PTO Switch Is Enabled. Warning Message Only To Inform Driver The Switch Is Now Active And Can Be Used. (CCU)

524267.15

Main Control Module Has Noted That A Forward/ Reverse Shuttle Was Done At A High Travel Speed. (PTR)